|
FRONT MATTER
| i |
| Part A Constitutive Modeling |
STUDY ON SOFTENING CONSTITUTIVE MODEL OF SOFT ROCK USING STRAIN SPACE BASED UNIFIED STRENGTH THEORY
LI SONG, CHONGDU CHO, SHENG LU and HONGJIAN LIAO | 3 |
DYNAMIC CRUSHING SIMULATION OF METALLIC FOAMS WITH RESPECT TO DEFORMATION AND ENERGY ABSORPTION
Y. F. ZHANG and L. M. ZHAO | 9 |
COMPARATIVE STUDY OF SINGLE CRYSTAL CONSTITUTIVE EQUATIONS FOR CRYSTAL PLASTICITY FINITE ELEMENT ANALYSIS
MYOUNG GYU LEE, ROBERT H. WAGONER and SUNG-JOON KIM | 16 |
PLASTIC DEFORMATION BEHAVIOR OF HIGH STRENGTH STEEL SHEET UNDER NON-PROPORTIONAL LOADING AND ITS MODELING
TAKESHI UEMORI, YUJI MITO, SATOSHI SUMIKAWA, RYUTARO HINO, FUSAHITO YOSHIDA and TETSUO NAKA | 22 |
A FULL CONSTITUTIVE RELATION OF SILICON–STEEL SHEET WITH ANISOTROPY CONSIDERED
S. M. BYON, U. K. YOO and Y. LEE | 28 |
SOME REMARKS ON RATE-SENSITIVITY OF NITI SHAPE MEMORY ALLOYS
OTTO T. BRUHNS | 34 |
CREEP ANALYSIS FOR A WIDE STRESS RANGE BASED ON STRESS RELAXATION EXPERIMENTS
HOLM ALTENBACH, KONSTANTIN NAUMENKO and YEVGEN GORASH | 41 |
DAMAGE-COUPLED CONSTITUTIVE MODEL FOR UNIAXIAL RATCHETING AND FATIGUE FAILURE OF 304 STAINLESS STEEL
GUOZHENG KANG, JUN DING and YUJIE LIU | 47 |
AN IMPROVED ANALYTICAL CONSTITUTIVE RELATION FOR NORMAL WEIGHT HIGH-STRENGTH CONCRETE
Z. H. LU and Y. G. ZHAO | 53 |
THERMOMECHANICAL RESPONSE OF THE ROTARY FORGED WHA OVER A WIDE RANGE OF STRAIN RATES AND TEMPERATURES
W. G. GUO, C. QU and F. L. LIU | 59 |
CREEP CONSTITUTIVE RELATIONSHIPS AND CYCLIC BEHAVIORS OF Sn96.5Ag3Cu0.5 UNDER HIGH TEMPERATURES
JI-HONG LIU, XIANG-QI MENG and JIN-QUAN XU | 66 |
| Part B Damage, Fracture, Fatigue and Failure |
PLASTIC DEFORMATION OF POLYMER INTERLAYERS DURING POST-BREAKAGE BEHAVIOR OF LAMINATED GLASS - PARTIM 2: EXPERIMENTAL VALIDATION
D. DELINCÉ, D. CALLEWAERT, W. VANLAERE, J. BELIS and J. DEPAUW | 75 |
STUDY ON THE FRACTURE BEHAVIOR OF W-NI-FE HEAVY ALLOYS
WEIDONG SONG, JIANGUO NING and HAIYAN LIU | 81 |
ANALYSIS OF COLLISION BETWEEN DRILLSTRING AND WELL SIDEWALL
G. H. ZHAO and Z. LIANG | 87 |
FE SIMULATION OF EDGE CRACK INITIATION AND PROPAGATION OF CONVENTIONAL GRAIN ORIENTATION ELECTRICAL STEEL
D. H. NA and Y. LEE | 93 |
PREDICTION OF THE DELAMINATION IN THE PEARLITIC STEEL FILAMENTS BY 3 DIMENAIONAL ATOM PROBE TOMOGRAPHY
Y. S. YANG, C. G. PARK, J. G. BAE and D. Y. BAN | 99 |
LOW CYCLE FATIGUE BEHAVIOR OF Zn-22Al ALLOY IN SUPERPLASTIC REGION AND NON-SUPERPLASTIC REGION
ATSUMICHI KUSHIBE, TSUTOMU TANAKA, YORINOBU TAKIGAWA and KENJI HIGASHI | 105 |
TEMPERATURE DEPENDENT FRACTURE MODEL AND ITS APPLICATION TO ULTRA HEAVY THICK STEEL PLATE USED FOR SHIPBUILDING
YUN CHAN JANG, YOUNGSEOG LEE, GYU BAEK AN, JOON SIK PARK, JONG BONG LEE and SUNG IL KIM | 111 |
INVESTIGATION OF FRETTING FATIGUE BEHAVIOR OF TI811 ALLOY AT ELEVATED TEMPERATURE
XIAO-HUA ZHANG and DAO-XIN LIU | 117 |
EFFECT OF VARIOUS HEAT TREATMENT PROCESSES ON FATIGUE BEHAVIOR OF TOOL STEEL FOR COLD FORGING DIE
S. U. JIN, S. S. KIM, Y. S. LEE, Y. N. KWON and J. H. LEE | 123 |
FATIGUE LIFE PREDICTION OF ROLLED AZ31 MAGNESIUM ALLOY USING AN ENERGY-BASED MODEL
SUNG HYUK PARK, SEONG-GU HONG, BYOUNG HO LEE and CHONG SOO LEE | 131 |
PLASTIC DEFORMATION OF POLYMER INTERLAYERS DURING POST-BREAKAGE BEHAVIOR OF LAMINATED GLASS - PARTIM 1: ANALYTICAL APPROACH
J. BELIS, D. DELINCÉ, D. CALLEWAERT, R. VAN IMPE and J. DEPAUW | 137 |
LOAD CARRYING CAPACITY OF CORRODED REINFORCED CONCRETE BEAMS SUBJECTED TO REPEATED LOAD
CONGQI FANG, MEIYING YI and SHUJIAN CHENG | 143 |
A MODEL FOR GALLING BEHAVIOR IN FORMING OF HIGH STRENGTH STEEL UNDER TENSION-BENDING
Y. K. HOU, W. G. ZHANG, Z. Q. YU and S. H. LI | 149 |
DYNAMIC FAILURE OF A SPOT WELD IN LAP–SHEAR TESTS UNDER COMBINED LOADING CONDITIONS
J. H. SONG, J. W. HA, H. HUH, J. H. LIM and S. H. PARK | 155 |
EVALUATION OF DAMAGE IN STEELS SUBJECTED TO EXPLOITATION LOADING - DESTRUCTIVE AND NON-DESTRUCTIVE METHODS
ZBIGNIEW L. KOWALEWSKI, SŁAWOMIR MACKIEWICZ, JACEK SZELĄŻEK, KRYSTYNA PIETRZAK and BOLESŁAW AUGUSTYNIAK | 161 |
FATIGUE PROPERTIES OF AUTOMOBILE HIGH-STRENGTH BOLTS
CONGLING ZHOU, SHIN-ICHI NISHIDA and NOBUSUKE HATTORI | 167 |
RESEARCH ON THE EFFECT OF LOADING CONDITIONS ON THE STRENGTH AND DEFORMATION BEHAVIORS OF ROCKS
PENG-ZHI PAN, XIA-TING FENG and HUI ZHOU | 173 |
| Part C Dynamic Loading and Crash Dynamics |
NUMERICAL SIMULATION OF DYNAMIC FAILURE FOR ALUMINA CERAMIC
HUILAN REN and JIANGUO NING | 181 |
ANALYSIS OF DYNAMIC STRESS-STRAIN RELATIONSHIP OF LOESS
HONGJIAN LIAO, ZHIGANG ZHANG, CHUNMING NING, JIAN LIU and LI SONG | 187 |
STUDY OF CUTTING AERIAL PMMA WITH MINIATURE DETONATION CORD
Z. Q. LI, L. M. ZHAO and Y. G. ZHAO | 194 |
A STUDY ON THE BEHAVIOR OF A THIN STS 304 SHEET WITH A FREE BOUNDARY CONDITIONS SUBJECTED TO IMPACT LOADING
D. G. AHN, G. J. MOON, C. G. JUNG and D. Y. YANG | 200 |
DESIGN OF THE CROSS SECTION SHAPE OF AN ALUMINUM CRASH BOX FOR CRASHWORTHINESS ENHANCEMENT OF A CAR
S. B. KIM, H. HUH, G. H. LEE, J. S. YOO and M. Y. LEE | 206 |
REGRESSION MODEL FOR LIGHT WEIGHT AND CRASHWORTHINESS ENHANCEMENT DESIGN OF AUTOMOTIVE PARTS IN FRONTAL CAR CRASH
GIHYUN BAE, HOON HUH and SUNGHO PARK | 212 |
AN EXPERIMENTAL STUDY ON THE IMPACT DEFORMATION AND THE STRAIN RATE SENSITIVITY IN SOME STRUCTURAL ADHESIVES
TOSHIMASA NAGAI, TAKESHI IWAMOTO, TOSHIYUKI SAWA, YASUHISA SEKIGUCHI, HIDEAKI KURAMOTO and NORIO UESUGI | 218 |
EFFECTS OF IMPACT VELOCITY AND SLENDERNESS RATIO ON DYNAMIC BUCKLING LOAD FOR LONG COLUMNS
K. MIMURA, T. UMEDA, M. YU, Y. UCHIDA and H. YAKA | 224 |
CRASHWORTHINESS DESIGN OF THE SHEAR BOLTS FOR LIGHT COLLISION SAFETY DEVICES
JIN SUNG KIM, HOON HUH and TAE SOO KWON | 231 |
COMPUTATIONAL PERFORMANCE EVALUATION OF A SIDE STRUCTURE CONSIDERING STAMPING EFFECTS
SE-HO KIM and KEE-POONG KIM | 237 |
A NEW METHOD FOR VIBRATION RESPONSE OF BEAM ON FOUNDATION UNDER MOVING LOAD
YOUZHE YANG and XIURUN GE | 243 |
| Part D Engineering Applications and Case Studies |
TRIMMING LINE DESIGN USING AN INCREMENTAL DEVELOPMENT METHOD AND A FINITE ELEMENT INVERSE METHOD
YOUN-JOON SONG, CHUN-DAL PARK, YOUNG-HO HAHN and WAN-JIN CHUNG | 251 |
EFFECTS OF HEAT TREATMENTS ON THE ON-LINE SERVICE LIFE OF A PRESS DIE MANUFACTURED BY W-EDM
KYE-KWANG CHOI and YONG-SHIN LEE | 259 |
CALCULATION OF THE ULTIMATE BEARING CAPACITY OF SOIL SLOPE BASED ON THE UNIFIED STRENGTH THEORY
HONGJIAN LIAO, ZONGYUAN MA and LIJUN SU | 265 |
TOP JOINT STUDY ON TEMPERATURE STRESS FOR SUPER-LONG SLAB-COLUMN STRUCTURE
MINGHAI DONG, LI SONG and YING SHAO | 271 |
A PROCESS MAP FOR SEQUENTIAL COMPRESSION-BACKWARD EXTRUSION OF AZ31 MG ALLOYS AT WARM TEMPERATURS
DUK-JAE YOON, EUNG-ZOO KIM, CHONG-DU CHO and YONG-SHIN LEE | 277 |
A NUMERICAL SIMULATION OF STRIP PROFILE IN A 6-HIGH COLD ROLLING MILL
XIAOZHONG DU, QUAN YANG, CHENG LU, ANH KIET TIEU and SHINIL KIM | 283 |
DYNAMIC SIMULATION OF THE TAILING PROCESS IN HOT FINISHING MILL
SHINIL KIM, CHENG LU, XIAOZHONG DU and ANH KIET TIEU | 289 |
FACTOR STUDY FOR THE SEPARATOR PLATE OF MCFC HAVING UNIFORM STIFFNESS AT ELEVATED TEMPERATURE
SANG-WOOK LEE, JUNG-HYUN KIM and JOONG-HWAN JUN | 295 |
A STUDY ON THE IMPROVEMENT OF THE ACCURACY OF A SHAVING PROCESS USING A PROGRESSIVE DIE
WAN-JIN CHUNG, KU-BOK HWANG, JONG-HO KIM and HO-YEUN RYU | 301 |
APPLICATION OF FORMING LIMIT CRITERIA BASED ON PLASTIC INSTABILITY CONDITION TO METAL FORMING PROCESS
SEONG-CHAN HEO, TAE-WAN KU, JEONG KIM, BEOM-SOO KANG and WOO-JIN SONG | 308 |
TOOL PATH DESIGN OF INCREMENTAL OPEN-DIE DISK FORGING USING PHYSICAL MODELING
SUNG-UK LEE and DONG-YOL YANG | 314 |
NUMERICAL OPTIMIZATION OF SHEET METAL FORMING PROCESS USING NEW FRACTURE CRITERION
A. HIRAHARA, R. HINO, F. YOSHIDA and V. V. TOROPOV | 320 |
STUDY FOR BLADE CERAMIC COATING DELAMINATION DETECTION FOR GAS TURBINE
CHOUL-JUN CHOI, SEUNG HYUN CHOI and JAE-YEOL KIM | 327 |
STUDY ON CORRELATION BETWEEN SHEAR WAVE VELOCITY AND GROUND PROPERTIES FOR GROUND LIQUEFACTION INVESTIGATION OF SILTS
AILAN CHE, XIANQI LUO, JINGHUA QI and DEYONG WANG | 333 |
A STUDY ON THE STABILITY OF EARTH DAM SUBJECTED TO THE SEISMIC LOAD
JINGHUA QI, AILAN CHE and XIURUN GE | 339 |
A STUDY OF THE RECONSTRUCTION OF ACCIDENTS AND CRIME SCENES THROUGH COMPUTATIONAL EXPERIMENTS
S. J. PARK, S. W. CHAE, S. H. KIM, K. M. YANG and H. S. CHUNG | 345 |
PREDICTION OF ROLLING FORCE USING AN ADAPTIVE NEURAL NETWORK MODEL DURING COLD ROLLING OF THIN STRIP
H. B. XIE, Z. Y. JIANG, A. K. TIEU, X. H. LIU and G. D. WANG | 351 |
AN INFLUENCE FUNCTION METHOD ANALYSIS OF COLD STRIP ROLLING
Z. Y. JIANG, D. W. WEI and A. K. TIEU | 356 |
EFFECT OF ASYMMETRICAL STAND STIFFNESS ON HOT ROLLED STRIP SHAPE
DIANYAO GONG, JIANZHONG XU, ZHENGYI JIANG, XIAOMING ZHANG, XIANGHUA LIU and GUODONG WANG | 362 |
RIGID-PLASTIC SEISMIC DESIGN OF REINFORCED CONCRETE SHEAR WALL
CHANG LIN FAN and SHAN YUAN ZHANG | 368 |
| Part E Experimental and Numerical Techniques |
NUMERICAL STUDY ON THE SHAPED CHARGES
TIANBAO MA, CHENG WANG and JIANGUO NING | 377 |
EXPERIMENTAL STUDY ON MECHANICAL PROPERTY OF STEEL REINFORCED CONCRETE L-SHAPED SHORT COLUMNS
ZHE LI, HAO QIN, HUI DANG, HUI LI and JIAN-SHAN ZHANG | 383 |
MICROSTRUCTURE AND CRYSTALLOGRAPHIC TEXTURE OF STRIP-CAST FE-3.2%SI STEEL SHEET
Y. B. XU, Y. M. YU, G. M. CAO, C. S. LI, G. D. WANG and Z. Y. JIANG | 390 |
FINITE ELEMENT SIMULATION OF PORE CLOSING DURING CYLINDER UPSETTING
MIN CHEOL LEE, SUNG MIN JANG, JU HYUN CHO and MAN SOO JOUN | 396 |
TENSILE TEST BASED MATERIAL IDENTIFICATION PROGRAM AFDEX/MAT AND ITS APPLICATION TO TWO NEW PRE-HEAT TREATED STEELS AND A CONVENTIONAL Cr-Mo STEEL
MAN-SOO JOUN, JAE-GUN EOM, MIN-CHEOL LEE, JEONG-HWI PARK and DUK-JAE YOON | 402 |
AN ELASTO-PLASTIC ANALYSIS OF SOLIDS BY THE LOCAL MESHLESS METHOD BASED ON MLS
Y. T. GU | 408 |
PREDICTION OF PLUG TIP POSITION IN ROTARY TUBE PIERCING MILL USING SIMULATION AND EXPERIMENT
HYOUNG WOOK LEE, GEUN AN LEE, EUNG ZU KIM and SEOGOU CHOI | 415 |
STUDY OF ACCURATE HIGH-SPEED TENSION TESTING METHOD
TSUTOMU UMEDA and KOJI MIMURA | 421 |
DYNAMIC MATERIAL PROPERTIES OF THE HEAT-AFFECTED ZONE (HAZ) IN RESISTANCE SPOT WELDING
JI-WOONG HA, JUNG-HAN SONG, HOON HUH, JI-HO LIM and SUNG-HO PARK | 428 |
AN INFLUENCE OF SELECTED MECHANICAL PARAMETERS OF MMC ON THE THERMAL SHOCK RESISTANCE
DARIUSZ RUDNIK, ZBIGNIEW KOWALEWSKI, KRYSTYNA PIETRZAK and ANDRZEJ WOJCIECHOWSKI | 435 |
NUMERICAL SIMULATIONS OF THE INFLUENCE OF STRIKER BAR LENGTH ON SHPB MEASUREMENTS
DONG WEI SHU, CHUN QI LUO and GUO XING LU | 441 |
QUANTITATIVE RELATIONSHIPS BETWEEN MICROSTRUCTURAL AND MECHANICAL PARAMETERS OF STEELS WITH DIFFERENT CARBON CONTENT
KRYSTYNA PIETRZAK, ADAM KLASIK, ZBIGNIEW KOWALEWSKI and DARIUSZ RUDNIK | 447 |
EXPERIMENT STUDY ON DYNAMIC STRENGTH OF LOESS UNDER REPEATED LOAD
ZHENGHUA XIAO, BO HAN, HONGJIAN LIAO and AKENJIANG TUOHUTI | 453 |
SHEAR STRENGTH PREDICTION OF RC BEAMS WRAPPED WITH FRP
SUYAN WANG, YINGWU ZHOU and HONGNAN LI | 459 |
STUDY ON STRESS-STRAIN RELATIONSHIPSHIP OF LOESS BASED ON TWIN SHEAR UNIFIED DAMAGE CONSTITUTIVE MODEL
BO HAN, HANGZHOU LI, HONG-JIAN LIAO and ZHENGHUA XIAO | 466 |
THE INFLUENCE OF STRAIN PATH ON BIAXIAL COMPRESSIVE BEHAVIOR OF AZ31 MAGNESIUM ALLOY
ICHIRO SHIMIZU, NAOYA TADA and KOSUKE NAKAYAMA | 472 |
3D FINITE ELEMENT MODELLING OF COMPLEX STRIP ROLLING
Z. Y. JIANG | 478 |
| Part F Molecular Dynamics |
THE STUDY ON THE GAS PERMEABILITIES OF THE ETHYLENE/1-HEXENE COPOLYMER BY MOLECULAR DYNAMICS SIMULATION
SIZHU WU, JUN YI, LISHU ZHANG, LIQUN ZHANG and JAMES E. MARK | 487 |
DYNAMICS BEHAVIOR ANALYSIS OF GLOBULAR PARTICLE IN RHEOLOGY MATERIAL WITH CONTROLLED SOLID FRACTION
KI-YOUNG KWON, CHUNG-GIL KANG and SANG-MAE LEE | 493 |
EFFECT OF HELICITY ON THE BUCKLING BEHAVIOR OF SINGLE-WALL CARBON NANOTUBES
JEEHYANG HUH and HOON HUH | 500 |
| Part G Nano, Meso, Micro and Crystal Plasticity |
ENERGY OF ARMCHAIR NANOTUBE USING THE MODIFIED CAUCHY-BORN RULE
S. LU, C. D. CHO and L. SONG | 509 |
FABRICATION OF POLYMER MASTER FOR ANTIREFLECTIVE SURFACE USING HOT EMBOSSING AND AAO PROCESS
HONG GUE SHIN, JONG TAE KWON, YOUNG HO SEO and BYEONG HEE KIM | 515 |
TEXTURE AND FORMABILITY DEVELOPMENT OF ASYMMETRY ROLLED AA 3003 AL ALLOY SHEET
INSOO KIM, SAIDMUROD AKRAMOV and HAE BONG JEONG | 523 |
NUMERICAL SIMULATION OF DEEP DRAWING PROCESS OF ALUMINUM ALLOY SHEET USING CRYSTAL PLASTICITY
JUNG GIL SHIM and YOUNG TAG KEUM | 529 |
AN INTEGRATED MICROMECHANICS MODELLING APPROACH FOR MICRO-FORMING SIMULATION
W. ZHUANG and J. LIN | 535 |
STRETCHING-INDUCED ORIENTATION TO IMPROVE MECHANICAL PROPERTIES OF ELECTROSPUN PAN NANOCOMPOSITES
X. X. HOU, X. P. YANG, F. ZHANG, S. Z. WU and E. WACLAWIK | 541 |
THE BENDABILITY AND FORMABILITY OF COLD ROLLED AND HEAT TREATED AZ31 MG ALLOY SHEETS
INSOO KIM and SAIDMUROD AKRAMOV | 547 |
THE DEVELOPMENT OF THE MICROCTRUCTURE AND TEXTURE IN COLD ROLLED AZ31 MG ALLOY SHEETS
INSOO KIM and SAIDMUROD AKRAMOV | 553 |
TEXTURE DEVELOPMENT AND DRAWABILITY OF FRICTIONALLY ROLLED AA 5052 AL ALLOY SHEET
INSOO KIM, SAIDMUROD AKRAMOV, HAE BONG JEONG and TAE KYOUNG NO | 559 |
GRAIN-SIZE DEPENDENT YIELD BEHAVIOR UNDER LOADING, UNLOADING AND REVERSE LOADING
NOBUTADA OHNO, DAI OKUMURA and TOMOYUKI SHIBATA | 565 |
FINITE ELEMENT MODELLING OF MICRO-CUTTING PROCESSES FROM CRYSTAL PLASTICITY
Y. P. CHEN, W. B. LEE, S. TO and H. WANG | 571 |
FINITE ELEMENT ANALYSIS OF THERMAL NANOINDENTATION PROCESS AND ITS EXPERIMENTAL VERIFICATION
HYUN-JUN OH, EUN-KYUNG LEE, CHUNG-GIL KANG and SANG-MAE LEE | 577 |
| Part H Phase Transformations |
EFFECT OF TRANSFORMATION VOLUME STRAIN ON THE SPHERICAL INDENTATION OF SHAPE MEMORY ALLOYS
WENYI YAN, QINGPING SUN and HONG-YUAN LIU | 585 |
CHARACTERIZATION OF BAINITIC MICROSTRUCUTRES IN LOW CARBON HSLA STEELS
JU SEOK KANG and CHAN GYUNG PARK | 593 |
EBSD STUDY ON THE EVOLUTION OF MICROSTRUCTURES DURING COMPRESSIVE DEFORMATION OF AN AUSTENITIC STAINLESS STEEL
JONG BAE JEON and YOUNG WON CHANG | 599 |
TEXTURES OF EQUAL CHANNEL ANGULAR PRESSED 1050 ALUMINUM ALLOY STRIPS
JAE YEOL PARK, SEUNG-HYUN HONG and DONG NYUNG LEE | 605 |
A STUDY ON IMPACT DEFORMATION AND TRANSFORMATION BEHAVIOR OF TRIP STEEL BY FINITE ELEMENT SIMULATION AND EXPERIMENT
TAKESHI IWAMOTO, TOSHIYUKI SAWA and MOHAMMED CHERKAOUI | 613 |
| Part I Plastic Instability and Strain Localization |
ENERGY ABSORPTION OF EXPANSION TUBE CONSIDERING LOCAL BUCKLING CHARACTERISTICS
KWANG-HYUN AHN, JIN-SUNG KIM and HOON HUH | 621 |
| Part J Plasticity in Advanced Materials |
CHANGE IN MICROSCOPIC HARDNESS DURING TENSILE PLASTIC DEFORMATION OF POLYCRYSTALLINE ALUMINUM AND TITANIUM
XIAOQUN WANG and TAKEJI ABE | 631 |
FLD OF AZ31 SHEET UNDER WARM STRETCHING AND ITS PREDICTION
TETSUO NAKA, YASUHIDE NAKAYAMA, TAKESHI UEMORI, RYUTARO HINO, FUSAHITO YOSHIDA, MASAHIDE KOHZU and KENJI HIGASHI | 638 |
EFFECT OF HIGH TEMPERATURE DEFORMATION ON THE LOW THERMAL EXPANSION BEHAVIOR OF FE-29%NI-17%CO ALLOY
K. A. LEE, J. NAMKUNG and M. C. KIM | 644 |
THE PLASTICITY OF MONOCRYSTALLINE SILICON UNDER NANOINDENTATION
LI CHANG and L. C. ZHANG | 650 |
CHARACTERIZATION OF ELECTRO-RHEOLOGCIAL FLUIDS UNDER HIGH SHEAR RATE IN PARALLEL DUCTS
X. W. ZHANG, C. B. ZHANG, T. X. YU and W. J. WEN | 657 |
| Part K Plasticity in Materials Processing Technology |
PREDICTION OF THE RESIDUAL STRESS IN THE PROCESS OF STRAIGHTENING WIRE
TAE WON KIM, MYOUNG GYU LEE, HYUNG-IL MOON, HYUNG JONG KIM and HEON YOUNG KIM | 667 |
FORMING LIMIT OF AZ31B MAGNESIUM ALLOY SHEET IN THE DEEP DRAWING WITH CROSS-SHAPED DIE
HEON YOUNG KIM, SUN CHUL CHOI, HYUNG JONG KIM, SEOK MOO HONG, YONG SEUNG SHIN and GEUN HO LEE | 673 |
MICRO FORMING OF GLASS MICROLENS ARRAY USING AN IMPRINTED AND SINTERED TUNGSTEN CARBIDE MICRO MOLD
JEONGWON HAN, BYUNG-KWON MIN and SHINILL KANG | 679 |
FAST SPRINGBACK SIMULATION OF BENDING FORMING BASED ON ONE-STEP INVERSE ANALYSIS
YI-DONG BAO, WEN-LIANG CHEN and HONG WU | 685 |
EFFECT OF INITIAL MICROSTRUCTURE ON HOT FORGING OF MG ALLOYS
Y. KWON, Y. LEE, S. KIM and J. LEE | 692 |
THE UNLOADING MODULUS OF AKDQ STEEL AFTER UNIAXIAL AND NEAR PLANE-STRAIN PLASTIC DEFORMATION
E. J. PAVLINA, B. S. LEVY, C. J. VAN TYNE, S. O. KWON and Y. H. MOON | 698 |
SPRING-BACK CHARACTERISTICS OF GRAIN-REFINED MAGNESIUM ALLOY ZK60 SHEET
SEONG-HOON KANG, YOUNG-SEON LEE and JUNG-HWAN LEE | 704 |
INCREMENTAL SHEET FORMING WITH LOCAL HEATING FOR LIGHTWEIGHT HARD-TO-FORM MATERIAL
R. HINO, F. YOSHIDA, N. NAGAISHI and T. NAKA | 710 |
INFLUENCE OF BILLET SIZE ON THE DEFORMATION INHOMOGENEITY OF MATERIAL PROCESSED BY EQUAL CHANNEL ANGULAR PRESSING
TAO SUO, YULONG LI and FENG ZHAO | 716 |
INFLUENCE OF SHOT PEENING ON SURFACE CHARACTERISTICS OF HIGH-SPEED STEELS
YASUNORI HARADA and KENZO FUKAURA | 722 |
COLD BUTT JOINING OF LIGHT METAL SHEET BY SHOT PEENING
YASUNORI HARADA and YUJI KOBAYASHI | 728 |
EVOLUTION OF STRAIN STATES AND TEXTURES IN AA 5052 SHEET DURING CROSS-ROLL ROLLING
S. H. KIM, D. G. KIM, H. G. KANG, M. Y. HUH, J. S. LEE and O. ENGLER | 734 |
MINIMUM WALL THICKNESS OF HOLLOW THREADED PARTS IN THREE-DIE COLD THREAD ROLLING
HUIPING QI, YONGTANG LI, JIANHUA FU and ZHIQI LIU | 740 |
REPLICATION OF NANO/MICRO QUARTZ MOLD BY HOT EMBOSSING AND ITS APPLICATION TO BOROSILICATE GLASS EMBOSSING
SUNG-WON YOUN, CHIEKO OKUYAMA, MASHARU TAKAHASHI and RYUTARO MAEDA | 746 |
| Part L Plasticity in Tribology |
COMPARING SLIDING-WEAR CHARACTERISTICS OF THE ELECTRO-PRESSURE SINTERED AND WROUGHT COBALT
J. E. LEE, Y. S. KIM and T. W. KIM | 755 |
| Part M Porous, Cellular and Composite Materials |
A PHENOMENOLOGICAL CONSTITUTIVE MODEL OF ALUMINUM ALLOY FOAMS AT VARIOUS STRAIN RATES
C. LI, Z. H. WANG, L. M. ZHAO and G. T. YANG | 763 |
EXPERIMENTAL INVESTIGATION ON FRACTURE TOUGHNESS OF INTERFACE CRACK FOR ROCK/CONCRETE
SHUICHENG YANG, LI SONG, ZHE LI and SONGMEI HUANG | 769 |
INVESTIGATION ON THE EQUIVALENT MATERIAL PROPERTY OF CARBON REINFORCED ALUMINUM LAMINATES
SEUNG-HO SONG, TAE-WAN KU, JEONG KIM, BEOM-SOO KANG and WOO-JIN SONG | 777 |
MECHANICAL PROPERTIES OF TITANIUM FOAM FOR BIOMEDICAL APPLICATIONS
SADAF KASHEF, JIANGUO LIN, PETER D. HODGSON and WENYI YAN | 783 |
HOMOGENIZED CREEP BEHAVIOR OF CFRP LAMINATES AT HIGH TEMPERATURE
Y. FUKUTA, T. MATSUDA and M. KAWAI | 789 |
INVESTIGATION ON THERMAL PROPERTIES OF Al/SiCp METAL MATRIX COMPOSITE BASED ON FEM ANALYSIS
EUSUN YU, JEONG-YUN SUN, HEE-SUK CHUNG and KYU HWAN OH | 795 |
MULTI-SCALE CREEP ANALYSIS OF PLAIN-WOVEN LAMINATES USING TIME-DEPENDENT HOMOGENIZATION THEORY: EFFECTS OF LAMINATE CONFIGURATION
K. NAKATA, T. MATSUDA and M. KAWAI | 801 |
BENDING BEHAVIOR OF SIMPLY SUPPOTED METALLIC SANDWICH PLATES WITH DIMPLED CORES
DAE-YONG SEONG, CHANG GYUN JUNG, DONG-YOL YANG and DONG GYU AHN | 807 |
PENETRATION ANALYSIS OF ALUMINUM ALLOY FOAM
NIANMEI ZHANG and GUITONG YANG | 813 |
TWO-SCALE ANALYSIS OF HONEYCOMBS INDENTED BY FLAT PUNCH
TAKASHI ASADA, YUJI TANAKA and NOBUTADA OHNO | 819 |
| Part N Structural Plasticity |
TUBE HYDROFORMING PROCESS DESIGNE OF TORSION BEAM TYPE REAR SUSPENSION CONSIDERING DURABILITY
KYUNG-TAEK LEE, HONG-JUEN BACK, HEE-TAEK LIM, IN-SUK OH and HEON-YOUNG KIM | 827 |
THE DEFORMATION OF THE MULTI-LAYERED PANEL OF SHEET METALS UNDER ELEVATED TEMPERATURES
SANG-WOOK LEE and DONG-UK WOO | 834 |
NUMERICAL ANALYSIS ON MAGNETIC-ELASTO-PLASTIC BUCKLING AND BENDING OF FERROMAGNETIC RECTANGULAR PLATE
YUANWEN GAO and HOON HUH | 840 |
LOAD-CARRYING CAPACITIES FOR CIRCULAR METAL FOAM CORE SANDWICH PANELS AT LARGE DEFLECTION
W. HOU, Z. WANG, L. ZHAO, G. LU and D. SHU | 846 |
EARLY YIELDING OF LIQUID-FILLED CONICAL SHELLS
W. VANLAERE, G. LAGAE, R. VAN IMPE, J. BELIS and D. DELINCÉ | 852 |
| Part O Superplasticity |
EXPERIMENTAL STUDY ON DEFORMATION MECHANISM OF AZ31 MAGNESIUM ALLOY UNDER VARIOUS TEMPERATURE CONDITIONS
TADASHI INABA, TAKAMASA YOSHIKAWA and MASATAKA TOKUDA | 861 |
| Part P Time-Dependent Deformation |
THERMAL VISCOELASTIC ANALYSIS OF PLASTIC COMPONENTS CONSIDERING RESIDUAL STRESS
CHEL WOO CHOI, KAB SIK JEOUNG, HYUNG-IL MOON and HEON YOUNG KIM | 869 |
PREDICTION OF A MODIFIED PTW MODEL FOR VARIOUS TAYLOR IMPACT TESTS OF TANTALUM
JONG-BONG KIM and HYUNHO SHIN | 875 |
EFFECTS OF TEMPERATURE AND FORMING SPEED ON PLASTIC BENDING OF ADHESIVELY BONDED SHEET METALS
MICHIHIRO TAKIGUCHI, TETSUYA YOSHIDA and FUSAHITO YOSHIDA | 881 |
ANALYSIS OF ELASTO-PLASTIC STRESS WAVES BY A TIME-DISCONTINUOUS VARIATIONAL INTEGRATOR OF HAMILTONIAN
SANG-SOON CHO, HOON HUH and KWANG-CHUN PARK | 887 |
VISCO-ELASTIC AND PLASTIC SINGULAR BEHAVIORS OF AN INTERFACE CORNER IN ELECTRONIC PACKAGES
JIN-QUAN XU, HUIMIAO ZHENG and HONGLAI ZHU | 893 |
| Back |
